Radio
*****

.. py:module:: radio

The ``radio`` module allows devices to work together via simple wireless
networks.

The radio module is conceptually very simple:

* Broadcast messages are of a certain configurable length (up to 251 bytes).
* Messages received are read from a queue of configurable size (the larger the queue the more RAM is used). If the queue is full, new messages are ignored.
* Messages are broadcast and received on a preselected channel (numbered 0-100).
* Broadcasts are at a certain level of power - more power means more range.
* Messages are filtered by address (like a house number) and group (like a named recipient at the specified address).
* The rate of throughput can be one of three pre-determined settings.
* Send and receieve bytes to work with arbitrary data.
* As a convenience for children, it's easy to send and receive messages as strings.
* The default configuration is both sensible and compatible with other platforms that target the BBC micro:bit.

To access this module you need to::

    import radio

We assume you have done this for the examples below.

Constants
=========

.. py:attribute:: RATE_250KBIT

    Constant used to indicate a throughput of 256 Kbit a second.

.. py:attribute:: RATE_1MBIT

    Constant used to indicate a throughput of 1 MBit a second.

.. py:attribute:: RATE_2MBIT

    Constant used to indicate a throughput of 2 MBit a second.


Functions
=========

.. py:function:: on()

    Turns the radio on. This needs to be explicitly called since the radio
    draws power and takes up memory that you may otherwise need.

.. py:function:: off()

    Turns off the radio, thus saving power and memory.

.. py:function:: config(**kwargs)

    Configures various keyword based settings relating to the radio. The
    available settings and their sensible default values are listed below.

    The ``length`` (default=32) defines the maximum length, in bytes, of a
    message sent via the radio. It can be up to 251 bytes long (254 - 3 bytes
    for S0, LENGTH and S1 preamble).

    The ``queue`` (default=3) specifies the number of messages that can be
    stored on the incoming message queue. If there are no spaces left on the
    queue for incoming messages, then the incoming message is dropped.

    The ``channel`` (default=7) can be an integer value from 0 to 100
    (inclusive) that defines an arbitrary "channel" to which the radio is
    tuned. Messages will be sent via this channel and only messages received
    via this channel will be put onto the incoming message queue. Each step is
    1MHz wide, based at 2400MHz.

    The ``power`` (default=6) is an integer value from 0 to 7 (inclusive) to
    indicate the strength of signal used when broadcasting a message. The
    higher the value the stronger the signal, but the more power is consumed
    by the device. The numbering translates to positions in the following list
    of dBm (decibel milliwatt) values: -30, -20, -16, -12, -8, -4, 0, 4.

    The ``address`` (default=0x75626974) is an arbitrary name, expressed as a
    32-bit address, that's used to filter incoming packets at the hardware
    level, keeping only those that match the address you set. The default used
    by other micro:bit related platforms is the default setting used here.

    The ``group`` (default=0) is an 8-bit value (0-255) used with the
    ``address`` when filtering messages. Conceptually, "address" is like a
    house/office address and "group" is like the person at that address to
    which you want to send your message.

    The ``data_rate`` (default=radio.RATE_1MBIT) indicates the speed at which
    data throughput takes place. Can be one of the following contants defined
    in the ``radio`` module : ``RATE_250KBIT``, ``RATE_1MBIT`` or
    ``RATE_2MBIT``.

    If ``config`` is not called then the defaults described above are assumed.

.. py:function:: reset()

    Reset the settings to their default values (as listed in the documentation
    for the ``config`` function above).

.. note::

    None of the following send or receive methods will work until the radio is
    turned on.

.. py:function:: send_bytes(message)

    Sends a message containing bytes.

.. py:function:: receive_bytes()

    Receive the next incoming message on the message queue. Returns ``None`` if
    there are no pending messages. Messages are returned as bytes.

.. py:function:: receive_bytes_into(buffer)

    Receive the next incoming message on the message queue. Copies the message
    into ``buffer``, trimming the end of the message if necessary.
    Returns ``None`` if there are no pending messages, otherwise it returns the length
    of the message (which might be more than the length of the buffer).

.. py:function:: send(message)

    Sends a message string. This is the equivalent of
    ``send_bytes(bytes(message, 'utf8'))`` but with ``b'\x01\x00\x01'``
    prepended to the front (to make it compatible with other platforms that
    target the micro:bit).

.. py:function:: receive()

    Works in exactly the same way as ``receive_bytes`` but returns
    whatever was sent.

    Currently, it's equivalent to ``str(receive_bytes(), 'utf8')`` but with a
    check that the the first three bytes are ``b'\x01\x00\x01'`` (to make it
    compatible with other platforms that may target the micro:bit). It strips
    the prepended bytes before converting to a string.

    A ``ValueError`` exception is raised if conversion to string fails.

Examples
--------

.. include:: ../examples/radio.py
    :code: python